User Tools

Site Tools


Translations of this page:

en:bpi-r64:storage

Table of Contents

storage

new way

With the opensource ATF we switched to full 64bit mode,fip (bl31+uboot) and fit kernel

Details on my ATF repo: https://github.com/frank-w/BPI-R64-ATF

sudo dd of=$target if=./fip_sdmmc.bin bs=512 seek=2048

legacy way

SD

PRELOADER=$TOPDIR/mt-pack/mtk/${TARGET_PRODUCT}/bin/preloader_bpi-r64_forsdcard-2k.img
ATF=$TOPDIR/mt-pack/mtk/${TARGET_PRODUCT}/bin/BPI-R64-atf.img
UBOOT=$TOPDIR/u-boot-mt/u-boot-mtk.bin

HEAD0=$TOPDIR/mt-pack/mtk/${TARGET_PRODUCT}/bin/BPI-R2-HEAD440-0k.img
HEAD1=$TOPDIR/mt-pack/mtk/${TARGET_PRODUCT}/bin/BPI-R2-HEAD1-512b.img

sudo dd if=$HEAD0 	of=$O bs=512 seek=0 #0
sudo dd if=$HEAD1 	of=$O bs=512 seek=1 #512 = 0x200

sudo dd if=$PRELOADER 	of=$O bs=1k seek=2 #2k = 0x800

sudo dd if=$ATF 	of=$O bs=1k seek=512 #512k = 0x80000

sudo dd if=$UBOOT 	of=$O bs=1k seek=768 #768k = 0xC0000

# partition1 /dev/sdc1 vfat 204800~327679
# partition2 /dev/sdc2 ext4 327680~end

root@x:~# sfdisk /dev/sdb < r64_parttable.dat
root@x:~# mkfs.vfat /dev/sdb1
root@x:~# mkfs.ext4 /dev/sdb2
root@x:~# fatlabel /dev/sdb1 BPI-BOOT
root@x:~# e2label /dev/sdb2 BPI-ROOT

https://github.com/BPI-SINOVOIP/BPI-R64-BSP/tree/master/mt-pack/mtk/bpi-r64/bin

only uboot-mtk.bin (with littlekernel=LK) works

A better ATF is mt7622_atf_push_wps_uboot_64.img (can be found on my gdrive too) supports booting 32bit uboot by default and 64bit uboot by pressing wps-button

http://forum.banana-pi.org/t/bpi-r64-current-u-boot-support/10077/79

EMMC

this Preloader have to be used: preloader_evb7622_64_foremmc.bin (copy on my gdrive)

- boot from sd-card

root@bpi-r64:~# ls /dev/mmcblk*                                                 
/dev/mmcblk0    /dev/mmcblk0p2  /dev/mmcblk1boot0  /dev/mmcblk1rpmb
/dev/mmcblk0p1  /dev/mmcblk1    /dev/mmcblk1boot1
#configure lan-port
root@bpi-r64:~# ip addr add 192.168.0.18/24 dev eth0
root@bpi-r64:~# ip route add default via 192.168.0.10
root@bpi-r64:~# echo "nameserver 192.168.0.10">/etc/resolv.conf
#download preloader and flash it
root@bpi-r64:~# wget https://github.com/BPI-SINOVOIP/BPI-R64-bsp-4.19/raw/master/mt-pack/mtk/bpi-r64/configs/default/linux-4.19/preloader_evb7622_64_foremmc.bin
root@bpi-r64:~# echo 0 > /sys/block/mmcblk1boot0/force_ro
root@bpi-r64:~# dd if=preloader_evb7622_64_foremmc.bin of=/dev/mmcblk1boot0

- boot0-block exists, but mmc-utils showing partconfig 0x0 (should be 0x48), emmc-boot hangs at bootrom:

Click to display ⇲

Click to hide ⇱

F0: 102B 0000
F5: 480A 0031
F5: 480A 0031
F3: 4000 0036
F2: 300C 0000
00: 1005 0000
F5: 480A 0031
F5: 480A 0031
F3: 4000 0036
F2: 300C 0000
01: 102A 0001
02: 1005 0000
BP: 0000 00C0 [0001]
T0: 0000 035F [000F]
System halt!
root@bpi-r64:~# ./mmc extcsd read /dev/mmcblk1 | grep 'PARTITION_CONFIG'                                                                                       
Boot configuration bytes [PARTITION_CONFIG: 0x00]
root@bpi-r64:~# ./mmc bootpart enable 1 1 /dev/mmcblk1                                                                                                         
root@bpi-r64:~# ./mmc extcsd read /dev/mmcblk1 | grep 'PARTITION_CONFIG'                                                                                       
Boot configuration bytes [PARTITION_CONFIG: 0x48]

This can also be done in recent uboot

mmc partconf 0
mmc partconf 0 1 1 0

after this steps preloader gets loaded (i had only flashed preloader here and nothing alse, so error is correct…full boot needs additional headers HEAD0,HEAD1,SD-Preloader,ATF and UBOOT)…

Click to display ⇲

Click to hide ⇱

F0: 102B 0000                                                                   
F5: 480A 0031                                                                   
F5: 480A 0031                                                                   
F3: 0000 0000                                                                   
V0: 0000 0000 [0001]                                                            
00: 0000 0000                                                                   
BP: 0000 0041 [0000]                                                            
G0: 0190 0000                                                                   
T0: 0000 039F [000F]                                                            
Jump to BL                                                                      
                                                                                
UNIVPLL_CON0 = 0xFE000000!!!                                                    
mt_pll_init: Set pll frequency for 25M crystal                                  
RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0                      
[PMIC_WRAP]wrap_init pass,the return value=0.                                   
[pmic_init] Preloader Start..................                                   
[pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2  0:E3                           
[pmic_init] Done...................                                             
Chip part number:7622A                                                          
MT7622 Version: 1.2.7, (iPA)                                                    
SSC OFF                                                                         
mt_pll_post_init: mt_get_cpu_freq = 1350000Khz                                  
mt_pll_post_init: mt_get_mem_freq = 1600000Khz                                  
mt_pll_post_init: mt_get_bus_freq = 1119920Khz                                  
[PLFM] Init I2C: OK(0)                                                          
                                                                                
[BLDR] Build Time: 20190927-141930                                              
==== Dump RGU Reg ========                                                      
RGU MODE:     4D                                                                
RGU LENGTH:   FFE0                                                              
RGU STA:      0                                                                 
RGU INTERVAL: FFF                                                               
RGU SWSYSRST: 8000                                                              
==== Dump RGU Reg End ====                                                      
RGU: g_rgu_satus:0                                                              
 mtk_wdt_mode_config  mode value=10, tmp:22000010                               
PL P ON                                                                         
WDT does not trigger reboot                                                     
WDT NONRST=0x20000000                                                           
WDT IRQ_EN=0x340003                                                             
RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3)                                    
[EMI] MDL number = 2                                                            
[EMI] DRAMC calibration start                                                   
                                                                                
[EMI] DRAMC calibration end                                                     
                                                                                
[EMI]rank0 size: 0x40000000                                                     
[MEM] complex R/W mem test pass                                                 
RAM_CONSOLE wdt status (0x0)=0x0                                                
[mmc_init]: msdc0 start mmc_init_host() in PL...                                
[msdc_init]: msdc0 Host controller intialization start                          
[SD0] Pins mode(1), none(0), down(1), up(2), keep(3)                            
[SD0] Pins mode(2), none(0), down(1), up(2), keep(3)                            
[info][msdc_set_startbit 1127] read data start bit at rising edge               
[info][msdc_config_clksrc] input clock is 400000kHz                             
[SD0] Bus Width: 1                                                              
[info][msdc_config_clksrc] input clock is 400000kHz                             
[info][msdc_set_startbit 1127] read data start bit at rising edge               
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) DIV(385) DS(0) RS(0)         
[msdc_init]: msdc0 Host controller intialization done                           
[mmc_init]: msdc0 start mmc_init_card() in PL...                                
[mmc_init_card]: start                                                          
[info][msdc_config_clksrc] input clock is 400000kHz                             
[info][msdc_set_startbit 1127] read data start bit at rising edge               
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) DIV(385) DS(0) RS(0)         
[SD0] Bus Width: 8                                                              
[SD0] Switch to High-Speed mode!                                                
[info][msdc_config_clksrc] input clock is 400000kHz                             
[info][msdc_set_startbit 1127] read data start bit at rising edge               
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) DIV(192) DS(0) RS(0)         
[SD0] Bus Width: 8                                                              
[SD0] Size: 7456 MB, Max.Speed: 52000 kHz, blklen(512), nblks(15269888), ro(0)  
[mmc_init_mem_card 3140][SD0] Initialized, eMMC50                               
before host->cur_bus_clk(259740)                                                
[info][msdc_config_clksrc] input clock is 400000kHz                             
[info][msdc_set_startbit 1127] read data start bit at rising edge               
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) DIV(1) DS(0) RS(0)       
host->cur_bus_clk(50000000)                                                     
[mmc_init_card]: finish successfully                                            
[PLFM] Init Boot Device: OK(0)                                                  
[GPT_PL](BPI)Parsing Primary GPT now...                                         
[GPT_PL]check header, err(signature 0x0000000000000000!=0x5452415020494645)     
[GPT_PL]Success to find valid GPT.                                              
                                                                                
[PART] blksz: 512B                                                              
[PART] [0x0000000000020000-0x000000000007FFFF] "preloader" (768 blocks)         
[PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (512 blocks)              
[PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (1024 blocks)               
                                                                                
Device APC domain init setup:                                                   
                                                                                
Domain Setup (0x0)                                                              
Domain Setup (0x0)                                                              
Device APC domain after setup:                                                  
Domain Setup (0x0)                                                              
Domain Setup (0x0)                                                              
[get_part] part->nr_sects=768, part->info->name=preloader                       
[get_part] part->nr_sects=512, part->info->name=tee1                            
[get_part] part->nr_sects=1024, part->info->name=lk                             
load lk (ret=-1)                                                                
[BLDR] Second Bootloader Load Failed                                            
PL fatal error...

maybe write partitiontable

Click to display ⇲

Click to hide ⇱

root@bpi-r64:~# sfdisk -d /dev/mmcblk0 > r64_parttable.dat
root@bpi-r64:~# sfdisk /dev/mmcblk1 < r64_parttable.dat
...
root@bpi-r64:~# ls /dev/mmcblk*
/dev/mmcblk0    /dev/mmcblk1       /dev/mmcblk1p1
/dev/mmcblk0p1  /dev/mmcblk1boot0  /dev/mmcblk1p2
/dev/mmcblk0p2  /dev/mmcblk1boot1  /dev/mmcblk1rpmb

boot from emmc till uboot: http://forum.banana-pi.org/t/bpi-r64-quick-start-boot-from-emmc/9809/36

i've created a small script with all headers needed for emmc-boot: https://drive.google.com/open?id=1a8yCzwiCAcqtHHXDLhRzMdItsMC7ndJr :!: this erases content of emmc! if you do not want this, comment out lines for writing partition table and formatting

en/bpi-r64/storage.txt · Last modified: 2023/06/08 17:06 by 127.0.0.1